Dissertações em Ciência e Engenharia de Materiais (Mestrado) - PPGCEM/Ananindeua
URI Permanente para esta coleçãohttps://repositorio.ufpa.br/handle/2011/12421
Navegar
Navegando Dissertações em Ciência e Engenharia de Materiais (Mestrado) - PPGCEM/Ananindeua por Afiliação "UFPA - Universidade Federal do Pará"
Agora exibindo 1 - 6 de 6
- Resultados por página
- Opções de Ordenação
Item Acesso aberto (Open Access) Caracterização do tecido fibroso de tururi e avaliação de propriedades mecânicas de compósitos de matriz poliéster reforçados com tecido fibroso de tururi(Universidade Federal do Pará, 2023-01-30) SANTOS, Avener Gleidson Andrade; CÂNDIDO, Verônica Scarpini; http://lattes.cnpq.br/8274665115727809; https://orcid.org/0000-0002-3926-0403In recent decades, the search for materials with high mechanical performance and that are in accordance with sustainability requirements has become increasing. In the context of sustainability, the United Nations (UN) established in 2015 the Sustainable Development Goals (SDGs), in order to guide the paths to sustainable development. The use of waste to produce new materials is beneficial, because the use of these materials represents a solution for environmentally friendly disposal, thus covering the requirements established by the SDGs. The use of natural fibers in the production of new materials has increased significantly in the last decade. The use of natural fibers as reinforcement in polymer matrix composites is already well established. This is due to the fact that some fibers have high mechanical performance and good thermal stability, two highly attractive properties in composite materials. Composites reinforced with natural fibers have a vast field of application, and can be used in civil construction, aerospace, and automotive industries, among others. In this scenario, the use of tururi fabric as a reinforcement agent in composites of polymeric matrix emerges as a viable alternative for sustainable disposal of this waste coming from the harvesting stage of its fruits. Thus, this study aims to characterize the tururi fibrous tissue by optical microscopy, scanning electron microscopy, X-ray diffraction, thermogravimetric analysis and Fourier transform infrared spectroscopy (FTIR), as well as to determine physical properties such as density, moisture content and weight. The composites were produced using a 2.5, 5.0 and 7.5% by mass percentage of reinforcement. Additionally, tensile, flexural and charpy impact tests were performed. The characterizations revealed that the tururi fibrous tissue is composed of fibers of various diameters and has regions of bifurcation, indicating that the tissue can act in different ways when incorporated as reinforcement. The density, moisture content and weight had average values of 1.17 g/cm3, 16.58% and 146.61 g/m2, respectively. The thermal analysis revealed good thermal stability for the tururi fabric. The mechanical tests pointed out that as the incorporation of reinforcement occurred, the composites tested in traction had a loss of resistance, presenting a loss of 15MPa in relation to the matrix. When requested in flexion the composites reinforced with up to 2.5% showed better mechanical performance, with values of 63.9 MPa. The impact test revealed that the energy absorption capacity increased by 371% compared to the matrix, which indicates that the fabric acted as a good reinforcement agent.Item Acesso aberto (Open Access) Código de resposta rápida nanoestruturado impresso em 3D(Universidade Federal do Pará, 2023-07-12) OLIVEIRA, Dhonata Sebastião Caldas; REIS, Marcos Allan Leite dos; http://lattes.cnpq.br/8252507933374637; https://orcid.org/0000-0003-2226-2653Due to the Fourth Industrial Revolution, also known as Industry 4.0, factories increasingly have systems dependent on the Internet and communication technologies, which guarantees them unprecedented efficiency, but makes them vulnerable to cyber attacks. For this reason, cybersecurity it is an increasingly relevant topic, with technologies such as blockchain and quantum cryptography based on physically unclonable functions (PUFs) presenting themselves as alternatives in this area. In this sense, this work presents the synthesis of poly(acrylonitrile-butadiene-styrene) (ABS) nanocomposites with respectively 1 and 2 % by mass of carbon nanotubes (CNTs) for the 3D printing of the so-called NanoCodecs, which present Raman spectral signatures, classified as PUFs, which can be used as cryptographic keys generated by a code built in the Python programming language. For this, two solutions were prepared, the first with multi-walled CNTs functionalized with carboxylic acid in acetone, and the other with pure ABS pellets in this same solvent. After mixing these solutions and ultrasonic baths, the acetone was evaporated and ABS/NTC1%m/m and ABS/NTC2%m/m pellets were produced, which were used for the production of nanostructured filaments in an extruder. Then NanoCodecs as quick response code (QR code) and as round/square stamps were 3D printed. The electrical characterization of samples printed with nanostructured filaments showed a reduction in electrical resistance with an increase in the percentage by mass of CNTs. Despite this, the morphological characterization by Scanning Electron Microscopy showed that there is a low concentration of nanotubes on the surface of the samples, which indicates that they are dispersed throughout the volume of the samples. The vibrational characterization by Raman spectroscopy was used to identify the characteristics of pure materials, both ABS and NTCs, and compare with the Raman spectrum of the ABS/NTCs nanocomposite. As a result, there was an overlap of the vibrational modes of both materials, with emphasis on the shift to the right of the sub-band 𝐺𝑒𝑥𝑡 in 8 𝑐𝑚−1, which indicates that the nanotubes are compressed in the polymeric matrix. Finally, using nanocomposites as PUFs, it was possible to generate keys from the main vibrational modes of these materials: the D, G and 2D bands of nanotubes and the bands named as 1001-PS and 2239-PAN of ABS. Therefore, the results obtained indicate that NanoCodecs can be used as elements of ybersecurity in Industry 4.0, through cryptographic keys generated by the spectral analisys of the nanocoposite used for produtction of the NanoCodecs.Item Acesso aberto (Open Access) Desenvolvimento de sensor piezorresistivo nanoestruturado impresso em 3D(Universidade Federal do Pará, 2023-07-05) QUARESMA, Luciano José Barbosa; REIS, Marcos Allan Leite dos; http://lattes.cnpq.br/8252507933374637; https://orcid.org/0000-0003-2226-2653; FEIO, Waldeci Paraguassu; http://lattes.cnpq.br/3512689932467320; https://orcid.org/0000-0003-4980-4694The emergence of smart factories based on Industry 4.0 increases the automation and optimization of industrial processes in production chains. In this context, the integration between physical and digital systems depends on intelligent sensors, with greater sensitivity and integrated by the Internet of Things (IoT). The literature indicates that piezoresistive sensors can be produced by additive manufacturing (AM) and nanostructured with carbon nanotubes (NTCs), which generate a nanoelectromechanical system (NEMS) after its dispersion in the material. Thus, this work presents the development of a low-cost piezoresistive nanoelectromechanical sensor, produced by applying layers of NTCs on poly(acrylonitrile-butadiene-styrene) (ABS) parts printed by fused deposition modeling (FDM), integrable to the Industry 4.0 via IoT through ESP32 microcontrollers. For this, a diaphragm-type sensor device with dimensions 17.8, 17.8 and 5.5 𝑚𝑚 was developed, whose sensor element deformation occurs by pressing a button. After MA printing of the device parts, carboxylic acid functionalized multi-walled CNTs (MWCNT-COOH) were dispersed by ultrasonic bath in a solution with a concentration of 1 𝑚𝑔/𝑚𝑙 of acetone and dimethylformamide, in a ratio of 1 ∶ 1 in volume, for coating the sensor elements in successive layers with an aerograph. After the deposition of five layers of CNTs on the polymeric substrate, measurements of electrical resistance obtained with a picoammeter showed the percolation of the material in the second layer, with initial values above 10 𝑇 Ω and final values below 100 𝑘 𝑂𝑚𝑒𝑔𝑎 after the fifth layer, which occurs by the formation of conduction channels originating from the random arrangement of CNTs on the ABS surface, as observed by Field Emission Scanning Electron Microscopy (FEG-SEM). After that, the electrical resistance was measured during pressure cycles with progressive load and with maximum load, in which the sensor elements presented an operating range of 139.97 ± 0.46 to 363.25 ± 0.39 𝑘𝑃 𝑎. In the first test, the minimum sensitivity of 0.1 % and maximum sensitivity of 1.16 %. In the second, the highest average sensitivity was 0.63 ± 0.04 % and the lowest average response and recovery times were 0.55 ± 0.29 𝑠 and 12.29 ± 1.44 𝑠, respectively. Raman spectroscopy showed the overlapping of the signals of each material, in particular the ABS band at 1447 𝑐𝑚−1 which appears prominently between the NTCs 𝐷 and 𝐺 bands. Based on the piezoresistive response that the material presented from the NEMS generated by the deposition of NTCs on ABS, this concept of a load cell can be integrated into an ESP32 microcontroller board, making it an intelligent device with potential application in industrial systems. 4.0.Item Acesso aberto (Open Access) Desenvolvimento de termosensores nanoestruturados impressos em 3D(Universidade Federal do Pará, 2023-06-26) SANTOS, Leandro José Sena; REIS, Marcos Allan Leite dos; http://lattes.cnpq.br/8252507933374637; https://orcid.org/0000-0003-2226-2653The market for temperature sensors and other related devices has grown significantly in recent years. It is estimated that there will be an annual growth rate of 11% between 2019 and 2026. This growth has sparked interest in studies focusing on alternative nanosensors that offer better portability, sustainability, and may contribute to achieving the Sustainable Development Goals (SDGs). This work presents the development of four sensors based on Poly (lactic acid) - PLA and Carbon Nanotubes - CNTs, produced using additive manufacturing. These sensors are designed for monitoring body temperature (35 to 45ºC) and cold room temperatures (5°C to -40°C), covering an active area of 15cm2. One of these sensors was developed using only PLA as a control sample, while the others were nanostructured by adding two different types of inks containing CNTs. The synthesis of these sensors was performed through 3D printing using Fused Deposition Modeling (FDM) technology, with a specific synthesis method for each sensor. Through morphological, vibrational, and electrical characterizations, the devices/sensors exhibited thermoresistive and thermoelectric responses to temperature variations. Electronic microscopy and vibrational Raman spectroscopy analyses of the nanocomposite samples revealed the successful incorporation of CNTs into the PLA matrix, as evident from their characteristic vibrational spectra. The sensors demonstrated a Seebeck coefficient of 1.33μV/K under temperature gradients of 300K, and a maximum thermoresistive response of -4.35± 0.15% at approximately 45°C. Thus, such developed devices exhibited the behavior of thermistors and thermocouples, making them a promising alternative for implementation in cold rooms and Home Health systems.Item Acesso aberto (Open Access) Estudo das propriedades mecânicas e microestruturais de materiais cimentícios geopoliméricos produzidos a partir de metacaulim e escória de alto forno(Universidade Federal do Pará, 2023-06-21) ALMEIDA, Bianca Mendes; SILVA, Alisson Clay Rios da; http://lattes.cnpq.br/7389345867032737; https://orcid.org/0000-0001-9186-2287The environmental impacts caused by the production of Portland Cement point to the urgency of reducing the use of this binder mainly due to the CO2 emission and energy consumption that occur during its production process. In the search for alternative materials, geopolymeric cement has shown promise, both in terms of mechanical performance and conservation of natural resources. These cements are obtained from natural raw materials containing aluminosilicates activated by an alkaline solution. In this work, geopolymeric cement paste, mortar and concrete were developed using metakaolin, blast furnace slag and alkaline solution of sodium hydroxide and sodium silicate. The main objectives included evaluating the influence of blast furnace slag on the mechanical properties of geopolymer pastes, varying its addition in mass (30% to 60%), evaluating the influence of sand in geopolymer mortar varying its addition in the paste with better performance of 20% to 70%, and finally, the addition of gravel 0 in two mixtures. The results showed that the paste reached a maximum compressive strength of 36.5 MPa with 35% slag in the matrix. This value rose to 41.15 MPa in the mortar with the incorporation of 40% sand. For concrete, the best result was found for the mixture that contained less crushed stone. The results of the concrete were compared with the CPV-ARI Portland cement concrete by setting some dosing parameters such as binder consumption and water/binder ratio. Other properties investigated included setting time, slump, flexural tensile strength and microstructural analysis by SEM. Geopolymeric concrete was superior to Portland by up to 21.16%, reaching compressive strength of 41.8 MPa, flexural traction of 4.87 MPa and better matrix/aggregate adhesion in the mixture with less addition of gravel 0. The results obtained for geopolymers enable their application in civil works that demand materials that reach high strenght in the initial ages, precast and paving industries.Item Acesso aberto (Open Access) Estudo de rotas tecnológicas para a síntese de geopolímeros com adição de micropartículas de vidro: análise da influência do tamanho e forma das partículas(Universidade Federal do Pará, 2025-02-14) MODESTO, Alex da Silva; SILVA, Alisson Clay Rios da; http://lattes.cnpq.br/7389345867032737; https://orcid.org/0000-0001-9186-2287The sustainable construction of the future requires materials that consume less energy, emit fewer greenhouse gases and reuse waste that is harmful to the environment, such as discarded glass, one of the main waste products in the production chain. This research developed geopolymers, inorganic polymers formed by the activation of amorphous aluminosilicates in an alkaline medium, using me-takaolin and blast furnace slag as precursors and recycled glass microparticles as an additive. Com-positions were formulated with glass contents ranging from 0% to 60%, in particle size ranges of < 38 μm, 38-45 μm, 45-75 μm and 75-180 μm, and alkaline hydroxide and sodium silicate activators. Compression tests carried out on cylindrical specimens after 7 days of curing revealed that the addi-tion of 40% glass with a grain size of 38-45 μm resulted in an 80% increase in compressive strength compared to the unmodified material, reaching values of over 40 MPa. Microstructural analysis by SEM and EDS confirmed greater density and reduced porosity in the geopolymer matrix. Tensile adhesion tests also indicated the viability of the material as a substrate for coatings, meeting the demands of the construction industry. It is concluded that geopolymers with added recycled glass combine high mechanical performance and sustainability, promoting circular economy and repre-senting a viable alternative to the use of Portland cement.