Navegando por Assunto "Cinza volante"

Agora exibindo 1 - 11 de 11

Acesso aberto (Open Access)
Estudo da reciclagem de cinza volante para produção de agregado sintético utilizando reator de leito fixo
(Universidade Federal do Pará, 2016-02-16) PEREIRA, Luiz Felipe Silva; SOUZA, José Antônio da Silva; http://lattes.cnpq.br/6157348947425968
The use of such industrial waste boiler fly ash for recycling and reuse, has intensified in recent years much for its physico-chemical characteristics that may result after the processing, in a material with good mechanical strength and can be designed for use in several areas such as construction. In this paper we obtain synthetic aggregates, after sintering process in a fixed bed reactor. For the production of aggregates pellet sewed up mixer from a mixing wheel boiler ash, clay and charcoal. After the process of ceramic sintering were measured material properties such that: porosity, density and water absorption. For the characterization of phases and mineralogical structures of the sintered material, we used the techniques of X-ray diffraction and scanning electron microscopy. Thus the contribution of this work is aimed at reducing environmental impacts, due to the possibility that the material produced has to replace natural aggregates.
Acesso aberto (Open Access)
Estudo da reciclagem de lodo de eta na fabricação de agregado sintético em mistura com cinza volante de carvão mineral
(Universidade Federal do Pará, 2016-11-22) SILVA, Elzelis Muller da; SOUZA, José Antônio da Silva; http://lattes.cnpq.br/6157348947425968
The Wastes (sludge) generated in the Water Treatment Plants (WTP) and fly ash from coal-fired power plants cause problems by the amount and concentration of harmful substances in them. Thus, this study aimed to produce synthetic aggregates using sludge WTP Bolonha (Belém/PA) and fly ash assessing their technical and environmental viability. The composition of the synthetic aggregates consisted of a high concentration of these residues in mixture with clay to molding and sintering at temperatures of 1200°C and 1250°C. The physical, mineralogical and microstructural analyzes of the synthetic aggregate were performed. Two concrete were produced, one with synthetic aggregate, and other references. In concrete were assessed their physical and mechanical properties in fresh and hardened state, and their microstructures. For the characterization of the concrete waste leaching and dissolution testing were performed. Synthetic aggregates were classified as lightweight aggregate for its low bulk density (<2.0 g / cm3) according to NBR 7211 (ABNT, 2009). The concrete produced with sintered aggregate (AGS-02) at 1250 °C was classified as non structural lightweight concrete according to the norms NBR 6118 (ABNT, 2014) and NBR 8953 (ABNT, 2015). The concrete of waste were classified as waste class IIB, non-hazardous and inert by NBR 10004 (ABNT, 2004) and within the limits of Resolutions No. 20/1986 and 430/2011 CONAMA into rivers class 2. It is noteworthy the synthetic aggregate meets the demands of the construction industry, reduces the consumption of raw materials and offers an alternative to the final disposal of waste.
Acesso aberto (Open Access)
Estudo da sinterização em reator vertical de leito fixo para produção de agregado sintético
(Universidade Federal do Pará, 2017-06) QUARESMA, Danielly da Silva; NEVES, Alacid do Socorro Siqueira; MELO, Alvino Oliveira; PEREIRA, Luiz Felipe Silva; BEZERRA, Pamela Tais Silva; MACÊDO, Emanuel Negrão; SOUZA, José Antônio da Silva
The synthetic aggregates are being employed in civil construction for the reduction of mineral extraction activities. Within this context, the recycling of industrial waste is the basis of the majority of processes to reduce the exploitation of mineral resources. In this work the sintering in a vertical fixed bed reactor for synthetic aggregate production using 20% pellets and 80% charcoal was studied. The pellets were prepared from a mixture containing clay, charcoal and fly ash. Two experiments varying the speed of air sucking were carried out. The material produced was analyzed by X-ray diffraction, scanning electron microscopy, measures of their ceramic properties, and particle size analysis. The results showed that the solid-state reactions, during the sintering process, were efficient and the produced material was classified as coarse lightweight aggregate. The process is interesting for the sintering of aggregates, and can be controlled by composition, particle size, temperature gradient and gaseous flow.
Acesso aberto (Open Access)
Estudo da sinterização em reator vertical de leito fixo: desenvolvimento de processo para produção de agregado sintético a partir de cinza volante e biomassa
(Universidade Federal do Pará, 2016-05-19) QUARESMA, Danielly da Silva; SOUZA, José Antônio da Silva; http://lattes.cnpq.br/6157348947425968; MACÊDO, Emanuel Negrão; http://lattes.cnpq.br/8718370108324505
The synthetic aggregates have been employed in civil construction as a measure for the reduction of mineral extraction. Within this context, the recycling of industrial waste configured today as the basis of the majority of processes to reduce the exploitation of mineral resources. This paper presents the formulation of a process of environmental character and self-sustaining from an energy point of view parameters to develop a process for the production of synthetic aggregate from fly ash and biomass fixed bed reactor. Thus, for the production of aggregate pellets were made from a mixture of clay, fly ash and charcoal in fixed proportions. The reactor is filled with 20% pellets (6.35 mm > pellet ≥ 4 mm) and 80% charcoal (3.36 mm > carbon ≥ 1.70 mm) rated for promoting the efficiency of combustion reactions and subsequent sintering process at different air velocities (Darcy at 20 °C) of 0.0059 m.s-1 (1º Experiment), 0.0098 m.s-1 (2º Experiment) and 0.017 m.s-1 (3º Experiment). By means of X-ray diffraction and scanning electron microscopy was identified the presence of mullite in synthetic aggregate. This material is characterized as lightweight aggregate, in accordance with current standards. With synthetic aggregates manufactured to lightweight concrete, according to the established standard, without structural function in civil construction, but with applications of moderate resistance and may be used in the counterfloor. The process if showed interesting for the sintering of aggregates with good adhesion to the matrix of cement, and can easily be controlled by composition, granulometry, temperature gradient and gaseous flow, reducing environmental impacts, to the extent that the material produced implies in not extraction of natural aggregates.
Acesso aberto (Open Access)
Estudo de parâmetros físicoquímicos para a produção de argamassas utilizando resíduos industriais e da construção civil
(Universidade Federal do Pará, 2014-02-26) FERREIRA, Keylla Castro; SOUZA, José Antônio da Silva; http://lattes.cnpq.br/6157348947425968
The mortas can be considered as a mixture of the binders and aggregates with water, having capacity of the induration and adherence. Instead, it is suggested the production of mortas using civil construction waste, with plenty silicoaluminates, obtained in demolitions and reforms of build, and fly ash as material pozzolana, obtained of the combustion of mineral coal in fluidized bed boilers, in partial replacement of Portland cement. The civil construction wastes were benefited and characterized by X-ray spectrometry and X-ray diffraction. The fly ash was characterized by granulometric analyze and X-ray spectrometry. The mortars of the were prepared using the following compositions of RCC, 95, 90, 85, 80, 75 and 70%; CV of 0, 5, 10, 15, 20 and 25% e 5% of Portland CP II Z 32 cement. In all the compositions were put 0,8% of water and the rheological testing was used the same proportions residue (RCC e CV) with 35% water. The specimens were cured for 28 days and after were submitted physical trials of absorption, porosity and bulk density; mechanical trials of resistance to compression and analysis of X-ray diffraction and scanning electron microscopy. The results obtained show that the recycling of civil construction waste and the use of fly ash and RCC is a promising technique in production of mortas.
Acesso aberto (Open Access)
Influência de aditivo polimérico no comportamento mecânico e reológico das argamassas produzidas com rejeitos industriais
(Universidade Federal do Pará, 2015-05-12) SILVA, André Luis Mileo Ferraioli; FELIPE, Augusta Maria Paulain Ferreira; http://lattes.cnpq.br/8871741271063047; SOUZA, José Antônio da Silva; http://lattes.cnpq.br/6157348947425968
Mortars are considered to be particulate systems in suspension with fine aggregate, binder, water and organic polymeric additive. Factors such as granulometry, cement, ash and additive contents in their composition influence mortar properties in both the fresh and hardened states. A rheological study and mechanical test were performed on mortar prepared for floors and coatings through incorporating civil construction wastes (RCC) such as fine aggregate and fly ash, a mineral waste derived from combustion in boilers at the HYDRO ALUNORTECompany. This study seeks to develop a polymeric mortar that uses CPII E-32RS Portland cement andflyashas binders and fine sand and RCC with polyvinyl acetate (PVA) as aggregates. A study was performed on the influence of cement, ash, granulometry of aggregates and use of PVA based-polymeric additives on mortar properties.The materials were submitted to physical and chemical characterization using granulometric analysis, X-ray fluorescence and FTIR. In preparing the specimens, 6 formulas with 5% cement and 3 formulas with 10% cement were used, both with different levels of ash, sand and RCC andmaintaining a constant level of Portland cement content. A comparison of the mechanical and rheological properties of formulas with and without PVA was also made.Formulas in a fresh state were submitted to rheological tests. After 28 days of curing specimens of these formulas, by then in a hardened state, were submitted to tests for mechanical resistance to compression, specific mass, apparent absorption and apparent porosity. The research demonstrated that employing a PVA-based polymeric additive improved the mechanical properties of the mortar prepared with industrial wastes, as well as guaranteeing satisfactory rheological behavior for possible applications of such mortars in civil construction.
Acesso aberto (Open Access)
Influência do teor de cinza volante na reologia de argamassa de assentamento: fabricado com reciclagem de resíduos
(Universidade Federal do Pará, 2014-02-05) CARDOSO, Dilson Nazareno Pereira; SOUZA, José Antônio da Silva; http://lattes.cnpq.br/6157348947425968; FELIPE, Augusta Maria Paulain Ferreira; http://lattes.cnpq.br/8871741271063047
The mortars may be considered as a set of solid suspended particles (aggregate), water and binders (cement slurry). Thus, rheological behavior during cure can be influenced by factors such as particle size, composition and content of corporate water. This study investigated the rheological properties of six mortars, depending on the content of fly ash as a pozzolanic activity material, partial replacement of cement. This type of cement used as an aggregate base construction of the residue (RCC) which was characterized by diffraction and fluorescence X- rays. Were formulated for the mortars with addition of rheological tests residue construction (RCC) in proportions of 95, 90, 85, 80, 75 and 70% fly ash (CV) 0, 5, 10, 15, 20 and 25 % to 5 % of ordinary Portland Cement (PC - II and 32), and in each sample was incorporated 35 % water. We used the model VT 550 viscometer with sensor type coaxial cylinders SV1 - Haake temperature of 28 ºC. To evaluate the curing time of the material has scheduled a constant shear rate 53.4 s-1 for 1h and 45 min, with rated torque at intervals of 15min. For the development of flow curves and hysteresis curves, we used the shear rate between 0 and 600 s-1 in the time interval of 120 s. The results showed that the incorporation of fly ash is the main factor for increased torque on the curing time of mortar and behavior change reópetico for thixotropic, the traits analyzed. The experimental data of the proposed formulations are adjusted to the rheological model of Herschel - Bulkley.
Acesso aberto (Open Access)
Produção de zeólita a partir de cinza volante de carvão mineral para adsorção de metais em chorume gerado no lixão/aterro controlado na Região Amazônica
(Universidade Federal do Pará, 2022-01-28) DIAS, Lianne Maria Magalhães; SOUZA, José Antônio da Silva; http://lattes.cnpq.br/6157348947425968
The formation of solid waste has become a great challenge for the environment preservation due to the lifestyle adopted by modern society, which seeks for practicality and immediacy, and by that, new products are released, and waste formation is increased. The decomposition of waste from various sources creates a dark liquid denominated “slurry”, which presents high concentration of organic and inorganic compounds. This study aimed to evaluate the concentrations of Cd, Cu, Cr, Mn, Ni, Pb, and Zn on the ground and percolated liquid produced at the solid waste decomposition site in the metropolitan region of Belém/Pará/Brazil. Fly ashes of mineral coal were used to produce a low-cost zeolitic material, for removing copper, zinc, cadmium, and chrome, which are present at the percolated liquid of the Aurá landfill. The zeolites synthesized by alkaline fusion (ZSH and ZSJ), and without alkaline fusion (ZSD, ZSG, ZSK, ZSO), were characterized by different techniques, such as X-ray fluorescenc espectrometry, X-ray diffraction, and Scanning Electron Microscopy. The treatment adsorption efficiency of using adsorbent zeolitic material demonstrated viability to be used as an adsorvent agent for the adsorption of metals present at the leachate produced by landfills.
Acesso aberto (Open Access)
Sinterização de pelotas de argila, carvão vegetal e cinza volante de caldeira em uma célula de combustão de leito fixo: análise da propagação da frente de reação de combustão no leito
(Universidade Federal do Pará, 2016-05-20) MELO, Alvino Oliveira; MACÊDO, Emanuel Negrão; http://lattes.cnpq.br/8718370108324505; MARTINS, Marcio Ferreira
A great preoccupation of humanity turns around the preservation of the environment, seeking to constantly through studies and search, alternatives to find a balance of coexistence between man and nature. Normally, industries in general, produce waste at its majority toxic which damage the environment, humans being and other diversities of life inserted in it. Looking up, insert itself in this context, this work makes a study of evolution of the temperature of combustion of a mixture, in predefined proportions of fly ash from boiler industries located in the State of Pará, clay from the banks of the Guamá River and charcoal acquired in metropolitan region of Belem-Pa, Brazil. The experiments were performed in a combustion reactor, acquired by Programa de Pós - Graduação em Engenharia de Recursos Naturais da Amazônia in order to assess the temperature profile of each experiment during the combustion process and if the values of these temperatures would be sufficient to initiate the process of sintering of the pellets. For the experiments performance, parameters such as inlet velocity of the fluid (air), diameters of the pellets (mixture of charcoal, ash and clay) and grain size of charcoal were varied and the effect of variations of these parameters were analyzed for each experiment. The historical temperatures were recorded by a data acquisition instrument named Paperless Recorder - PHL and subsequently plotted for analysis. Temperatures varying in the range of 800°C - 1290°C, were obtained and these values are sufficient to initiate the process of sintering of the pellets. Data generated by the combustion reactor were recorded by "Paperless Recorder" and compared with numerical results computational.
Acesso aberto (Open Access)
Síntese de zeólitas a partir de cinza volante de caldeiras: caracterização física, química e mineralógica
(2012-03) ROCHA JUNIOR, Carlos Augusto Ferreira da; SANTOS, Suzianny Cristina Arimatéa; SOUZA, Célio Augusto Gomes de; ANGÉLICA, Rômulo Simões; NEVES, Roberto de Freitas
Along the years, worldwide industrial development has causing a growing generation of residues, bringing potentials environmental problems. A study of the characteristics of these wastes, as well as the development of techniques for their use in new processes becomes indispensable for the environment preservation. The main purpose of this work is to evaluate the possible use of two important industrial residues from the Amazon region for zeolite synthesis: (a) the fly ash (particle size < 100 µm) that comes from burning of mineral coal in boiler; and (b) the microsilica, a by-product of the reaction between quartz and coal in the production of metallic silicon and alloys iron-silicon.The following chemical, physical and mineralogical characterization methods were carried out: X-ray diffractometry, X-ray fluorescence, scanning electron microscopy, granulometric analysis, differential thermal and thermogravimetric analysis (DTA-TG). The analyses were carried out at the following conditions: 60, 100, 150 and 190 °C, Na2O/A2O3 molar ratio of 5 and Si/Al molar ratio ranging from 2.12 to 15, and reaction time of 24 h. The results of the fly characterization demonstrate its enormous potential as raw material for the zeolite synthesis. SiO2 and Al2O3 represent more than 50% of its composition, mineralogical phases defined, low humidity content, low particle size (d90 < 10 µm), among others. Mineralogical analyses of the synthesized products showed the formation of some zeolite types, as follow: analcime, phillipsite, sodalite, zeolite P and tobermorite. The results show that the mixture fly ash-microsilica in these reaction conditions point to a promising material for zeolite synthesis.
Acesso aberto (Open Access)
Síntese hidrotérmica de zeólitas a partir de cinza volante de carvão mineral: aplicação na adsorção de íon amônio
(Universidade Federal do Pará, 2018-10) MAUES, Tamiris Cristina de Lima; ROCHA JUNIOR, Carlos Augusto Ferreira da; SOUZA, José Antônio da Silva
Fly ash is the main industrial waste generated by coal in steam and power plans. In Brazil, 1,4 million tons are produced every year. These ashes can be converted into zeolite products by alkaline hydrothermal treatment. The main objective of this paper was to induce this reaction which produces only zeolitic crystalline phases for ammonium ion absorption. So, some syntheses were done by different hydrothermal method (classical or two stages), work time (24 or 30 h) and many NaOH bulks. The characterization of ash (in natura and calcined) and products was performed by X-ray diffraction method, scanning electron microscopy and, in some cases, differential thermal and thermogravimetric analysis The product by two stages method was used in ammonium ion absorption in solution at Sips Mathematic Model: the highest capacity of 2,71 mg.g-1.